发布时间： 14:58:19
编辑：www.fx114.net
本篇文章主要介绍了"EIGRP1"，主要涉及到EIGRP1方面的内容，对于EIGRP1感兴趣的同学可以参考一下。
&&增强内部网关路由协议(Enhanced Interior Gateway Routing Protocol, EIGRP)。
&&1.基础配置命令：
&& router eigrp 1
&& & & &network 10.0.0.0 0.0.255.255
&& & & &network 192.168.9.0
&& 重要的EIGRP验证命令
show ip eigrpinterfaces
show ip protocols
show ip eigrp neighbors
show ip eigrp topology
show ip route
&& 2.Eigrp工作步骤：
1） 邻居发现： Eigrp路由器发送Hello消息，这旨在发现潜在的EIGRP邻接路由器并执行基本的参数检查；以确定哪些路由器应成为邻居。
2） 拓扑信息的交换：建立邻接关系后，邻居彼此交换完整的拓扑更新；从此以后，仅在网络拓扑发生变化时交换部分更新。
3） 选择路由： 每台路由器都分析其EIGRP拓扑表，并选择前往每个子网的度量值最低的路由。
&& & & &最佳路由选择的标准： 默认度量值 = （10*10*10*10*10*10*10/最小带宽 + 累积延迟）*256
&& &3.EIGRP邻接关系
1）操纵EIGRP Hello定时器和保持定时器
相关配置命令：
interface Fastethernet0/1
&&ip hello-interval eigrp 1 2
&& & & & & & & & &ip hold-time eigrp 1 6
2）使用被动接口建立邻接关系
相关配置命令:
router eigrp 1
&passive-interface fastethernet0/0
&passive-interface fastethernet0/1
&network 10.0.0.0
&network 192.168.9.0
3）使用EIGRP身份验证控制邻接关系
相关配置命令：
key chain carkeys
&&key-string fred
&&key-string wilma
interface FastEthernet0/1
&ip address172.16.1.1 255.255.255.0
&ip authentication mode eigrp 1 md5
&ip authentication key-chain eigrp 1 carkeys
4)使用静态配置控制邻接关系
相关配置：
router eigrp 1
&network 192.16.0.0
&no auto-summary
&Neighbor 10.10.15.5 Serial0/1
5)通过wan建立Eigrp邻接关系
在典型的LAN和典型的WAN技术中，EIGRP配置和邻接关系规则完全相同，但存在一些设计和运行方面的差别，尤其在路由器将与那些路由器成为邻居方面。主要有三种方式：帧中继，MPLS VPN，城域网
版权声明：本文为博主原创文章，未经博主允许不得转载。
一、不得利用本站危害国家安全、泄露国家秘密，不得侵犯国家社会集体的和公民的合法权益，不得利用本站制作、复制和传播不法有害信息！
二、互相尊重，对自己的言论和行为负责。
本文标题：
本页链接：温馨提示！由于新浪微博认证机制调整，您的新浪微博帐号绑定已过期，请重新绑定！&&|&&
LOFTER精选
网易考拉推荐
用微信&&“扫一扫”
将文章分享到朋友圈。
用易信&&“扫一扫”
将文章分享到朋友圈。
修改间隔的命令为：interface s0/0&ip hello-interval eigrp 1 2 & 其中1为自治域系统号，2为hello时间间隔&ip hold-time eigrp 1 6，其中1为自治域系统号，6为保持计时器时间查看修改后的配置R1#show ip eigrp interfaces detailIP-EIGRP interfaces for process 1& & & & & & & & & & & & Xmit Queue & Mean & Pacing Time & Multicast & &PendingInterface & & & &Peers &Un/Reliable &SRTT & Un/Reliable & Flow Timer & RoutesSe0/0 & & & & & & &1 & & & &0/0 & & & 205 & & & 0/15 & & & & 927 & & & & & 0& Hello interval is 1 sec& Next xmit serial &none&& Un/reliable mcasts: 0/0 &Un/reliable ucasts: 2/10& Mcast exceptions: 0 &CR packets: 0 &ACKs suppressed: 4& Retransmissions sent: 2 &Out-of-sequence rcvd: 0& Authentication mode is not set& Use unicast实验配置按照上图配置好借口地址与EIGRP1.0.0.1 --& 2.0.0.2 &是通过fram-relay网络传输，我们可以做如下测试将R2的s0/0接口手动shutdown后，1.0.0.1 --& 2.0.0.2 多长时间能通测试方法R1#ping 2.0.0.2 source loopback 0 repeat 1000 timeout 1Type escape sequence to abort.Sending -byte ICMP Echos to 2.0.0.2, timeout is 1 seconds:Packet sent with a source address of 1.0.0.1!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...!!!!!!!!!!!!!!!!要求：如果要求在R2的s0/0接口shutdown后5秒内 1.0.0.1 --&2.0.0.2 能够ping通修改方法：在R1和R2的s0/0接口上做如下配置即可interface s0/0&ip hello-interval eigrp 1 1&ip hold-time eigrp 1 3其中前面的1为EIGRP的自治域系统号
阅读(3993)|
用微信&&“扫一扫”
将文章分享到朋友圈。
用易信&&“扫一扫”
将文章分享到朋友圈。
历史上的今天
loftPermalink:'',
id:'fks_082070',
blogTitle:'EIGRP 修改hello时间间隔',
blogAbstract:'EIGRP中在T1（1.54Mbps）链路中的hello时间间隔默认为60秒& & & & & & & & &大于T1链路时hello的时间间隔默认为5秒修改间隔的命令为：interface s0/0&ip hello-interval eigrp 1 2 & 其中1为自治域系统号，2为hello时间间隔&ip hold-time eigrp 1 6，其中1为自治域系统号，6为保持计时器时间查看修改后的配置R1#show ip eigrp interfaces detail',
blogTag:'eigrp配置hello间隔',
blogUrl:'blog/static/',
isPublished:1,
istop:false,
modifyTime:7,
publishTime:7,
permalink:'blog/static/',
commentCount:0,
mainCommentCount:0,
recommendCount:0,
bsrk:-100,
publisherId:0,
recomBlogHome:false,
currentRecomBlog:false,
attachmentsFileIds:[],
groupInfo:{},
friendstatus:'none',
followstatus:'unFollow',
pubSucc:'',
visitorProvince:'',
visitorCity:'',
visitorNewUser:false,
postAddInfo:{},
mset:'000',
remindgoodnightblog:false,
isBlackVisitor:false,
isShowYodaoAd:false,
hostIntro:'.cn',
hmcon:'0',
selfRecomBlogCount:'0',
lofter_single:''
{list a as x}
{if x.moveFrom=='wap'}
{elseif x.moveFrom=='iphone'}
{elseif x.moveFrom=='android'}
{elseif x.moveFrom=='mobile'}
${a.selfIntro|escape}{if great260}${suplement}{/if}
{list a as x}
推荐过这篇日志的人：
{list a as x}
{if !!b&&b.length>0}
他们还推荐了：
{list b as y}
转载记录：
{list d as x}
{list a as x}
{list a as x}
{list a as x}
{list a as x}
{if x_index>4}{break}{/if}
${fn2(x.publishTime,'yyyy-MM-dd HH:mm:ss')}
{list a as x}
{if !!(blogDetail.preBlogPermalink)}
{if !!(blogDetail.nextBlogPermalink)}
{list a as x}
{if defined('newslist')&&newslist.length>0}
{list newslist as x}
{if x_index>7}{break}{/if}
{list a as x}
{var first_option =}
{list x.voteDetailList as voteToOption}
{if voteToOption==1}
{if first_option==false},{/if}&&“${b[voteToOption_index]}”&&
{if (x.role!="-1") },“我是${c[x.role]}”&&{/if}
&&&&&&&&${fn1(x.voteTime)}
{if x.userName==''}{/if}
网易公司版权所有&&
{list x.l as y}
{if defined('wl')}
{list wl as x}{/list}引用地址：Your ads will be inserted here byEasy Plugin for AdSense.Please go to the plugin admin page toPaste your ad code OR Suppress this ad slot.
提问 配置网络使用EIGRP路由协议
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#interface Ethernet0
Router1(config-if)#ip address 192.168.20.1 255.255.255.0
Router1(config-if)#exit
Router1(config)#interface Serial0.1 point-to-point
Router1(config-subif)#ip address 172.25.2.2 255.255.255.252
Router1(config-subif)#exit
Router1(config)#router eigrp 55
Router1(config-router)#network 172.25.0.0
Router1(config-router)#network 192.168.20.0
Router1(config-router)#exit
Router1(config)#end
注释 要确保启用此路由协议的所有路由器配置的EIGRP后面的进程号相同，可以使用show ip eigrp neighbors 来验证邻居关系。同时支持network 192.168.20.0 0.0.0.255 来定义发布的网络
7.2.      路由过滤
提问 对EIGRP学到或者宣告的路由进行过滤
入方向过滤
Router2#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router2(config)#access-list 34 deny 192.168.30.0
Router2(config)#access-list 34 permit any
Router2(config)#router eigrp 55
Router2(config-router)#distribute-list 34 in Serial0.1
Router2(config-router)#exit
Router2(config)#end
出方向过滤
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#access-list 57 permit 172.25.1.0
Router1(config)#access-list 57 deny any
Router1(config)#router eigrp 55
Router1(config-router)#distribute-list 57 out Serial0/0.2
Router1(config-router)#exit
Router1(config)#end
使用prefix方式过滤，并且支持gateway 选项
Router9#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router9(config)#ip prefix-list ALLOWED-PREFIXES permit 10.0.0.0/8 le 32
Router9(config)#ip prefix-list ALLOWED-PREFIXES deny 0.0.0.0/0 le 32
Router9(config)#ip prefix-list ALLOWED-NEIGHBORS permit 172.18.19.1/32
Router9(config)#ip prefix-list ALLOWED-NEIGHBORS permit 172.18.19.4/32
Router9(config)#ip prefix-list ALLOWED-NEIGHBORS deny 0.0.0.0/0 le 32
Router9(config)#router eigrp 55
Router9(config-router)#distribute-list prefix ALLOWED-PREFIXES gateway ALLOWED-NEIGHBORS in
Router9(config-router)#exit
Router9(config)#end
注释 在路由过滤时推荐使用prefix方式而不用ACL形式。Gateway参数只能用于入方向控制，同时建议不用和interface混和使用
7.3.      再发布路由到EIGRP  提问 再发布其他方式学到的路由到EIGRP路由进程
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#router eigrp 55
Router1(config-router)#redistribute rip
Router1(config-router)#default-metric
Router1(config-router)#exit
Router1(config)#end
注释 如果再发布的是静态路由可以不用配置default-metric命令，对于其他协议都必须配置此命令否则无法成功再发布。再发布之前也可以使用过滤列表进行路由过滤，从而只再发布特定路由
Router1(config)#router eigrp 55
Router1(config-router)#redistribute ospf 99
Router1(config-router)#distribute-list 7 out ospf 99
7.4.      使用Route Map方式来配置再发布
提问 使用控制粒度更好的Route Map方式来配置再发布
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#ip route 192.168.10.0 255.255.255.0 172.22.1.4
Router1(config)#ip route 192.168.11.0 255.255.255.0 172.22.1.4
Router1(config)#ip route 192.168.12.0 255.255.255.0 172.22.1.4
Router1(config)#access-list 20 permit 192.168.10.0
Router1(config)#access-list 21 permit 192.168.11.0
Router1(config)#route-map STATIC permit 10
Router1(config-route-map)#match ip address 20
Router1(config-route-map)#set metric 56 100 255 1 1500
Router1(config-route-map)#set tag 2
Router1(config-route-map)#exit
Router1(config)#route-map STATIC permit 20
Router1(config-route-map)#match ip address 21
Router1(config-route-map)#set metric 128 200 255 1 1500
Router1(config-route-map)#exit
Router1(config)#route-map STATIC deny 30
Router1(config-route-map)#exit
Router1(config)#router eigrp 55
Router1(config-router)#redistribute static route-map STATIC
Router1(config-router)#exit
Router1(config)#end
注释 此处配置和前面6.3的配置差不多，唯一需要注意的就是前面提到的必须要加上metric的设置
7.5.      特定接口禁止EIGRP
提问 禁止某个端口参与EIGRP
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#router eigrp 55
Router1(config-router)#passive-interface Serial0/1
Router1(config-router)#exit
Router1(config)#end
注释 这里的被动接口和RIP不同，由于结果是不能形成邻居在此接口所以使用该命令以后就不能发送也不能接收路由信息
7.6.      调整EIGRP度量值
提问 修改学到的EIGRP路由器度量值
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#access-list 22 permit 192.168.30.0
Router1(config)#access-list 33 permit 192.168.30.0
Router1(config)#router eigrp 55
Router1(config-router)#offset-list 33 out 10000 Serial0.1
Router1(config-router)#offset-list 22 in 10000 Serial0.1
Router1(config-router)#exit
Router1(config)#end
7.7.      定时器调整
提问 调整定时器优化收敛
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#interface Serial0.1
Router1(config-subif)#ip hello-interval eigrp 55 3
Router1(config-subif)#ip hold-time eigrp 55 9
Router1(config-subif)#exit
Router1(config)#end
注释 EIGRP的一个特性就是定时器的调整可以基于端口，并且不用保持整个网络中所有设备的定时器设置一致，各个定时器都是独立的
7.8.      启用EIGRP认证
提问 增强路由信息安全性
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#key chain ORA
Router1(config-keychain)#key 1
Router1(config-keychain-key)#key-string oreilly
Router1(config-keychain-key)#exit
Router1(config-keychain)#exit
Router1(config)#interface Serial0/1
Router1(config-if)#ip authentication mode eigrp 55 md5
Router1(config-if)#ip authentication key-chain eigrp 55 ORA
Router1(config-if)#exit
Router1(config)#end
注释 注意这里只是认证不是加密路由信息包。下面提供一种更改key方法，帮助网络平稳过渡到新的key
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#key chain Mars
Router1(config-keychain)#key 1
Router1(config-keychain-key)#key-string rocket
Router1(config-keychain-key)#accept-lifetime 00:00:00 Jan 1 :00 Nov 1 2006
Router1(config-keychain-key)#send-lifetime 00:00:00 Jan 1 :00 Nov 1 2006
Router1(config-keychain-key)#key 2
Router1(config-keychain-key)#key-string martian
Router1(config-keychain-key)#accept-lifetime 23:45:00 Oct 31 2006 infinite
Router1(config-keychain-key)#send-lifetime 00:00:00 Nov 1 2006 infinite  Router1(config-keychain-key)#end
7.9.      配置EIGRP路由汇总
提问 通过路由汇总来减少路由表大小和增强稳定性
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#interface Serial0/0.2
Router1(config-subif)#ip summary-address eigrp 55 172.25.0.0 255.255.0.0
Router1(config-subif)#exit
Router1(config)#end
缺省会自动路由汇总，使用no auto-summary关闭（12.2(8)T后自动关闭）
同时可以配置汇总路由的同时，宣告部分子网路由
Router9# configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router9(config)#ip prefix-list 10.5.5/24 permit 10.5.5.0/24
Router9(config)#route-map LEAK10-5-5 permit 10
Router9(config-route-map)#match ip address prefix-list 10.5.5/24
Router9(config-route-map)#exit
Router9(config)#interface Serial0/0
Router9(config-if)#ip summary-address eigrp 55 10.5.0.0 255.255.0.0 leak-map LEAK10-5-5
Router9(config-if)#exit
Router9(config)#end
注释 路由汇总也是EIGRP的特性之一，可以配置在任意路由器的接口进行汇总，不象OSPF那样只能在ABR汇总。汇总路由的度量值和所汇总路由中的最好的子网路由的度量值一致。Leakmap特性在12.3(14)T后引入，可以在汇总路由的同时发布某些更匹配的路由
7.10.      记录邻居状态变化
提问 记录邻居状态变化
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#router eigrp 55
Router1(config-router)#eigrp log-neighbor-changes
Router1(config-router)#exit
Router1(config)#end
注释 缺省开启
&!–[if !supportLists]&#.           &!–[endif]–&限制EIGRP路由更新占用带宽
提问 限制EIGRP路由更新占用带宽的百分比
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#interface Serial0.1
Router1(config-subif)#ip bandwidth-percent eigrp 55 40
Router1(config-subif)#exit
Router1(config)#end
注释 这里的百分比可以大于100％，当我们人为的设定了某端口带宽用于计算度量值时
7.12.      EIGRP Stub路由
提问 向边缘网络发布较小的路由表
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#router eigrp 55
Router1(config-router)#eigrp stub
Router1(config-router)#exit
Router1(config)#end
7.13.      路由标签
提问 通过对特定路由进行标签，防止再分发时出现路由回环
Router1#configure terminal
Enter configuration commands, one per line.      End with CNTL/Z.
Router1(config)#ip route 0.0.0.0 0.0.0.0 172.25.1.1
Router1(config)#access-list 7 permit 0.0.0.0
Router1(config)#route-map TAGGING permit 10
Router1(config-route-map)#match ip address 7
Router1(config-route-map)#set tag 5
Router1(config-route-map)#exit
Router1(config)#router eigrp 55
Router1(config-router)#redistribute static route-map TAGGING
Router1(config-router)#exit
Router1(config)#end
&!–[if !supportLists]&#.           &!–[endif]–&查看EIGRP状态
提问 查看状态命令
Router1#show ip protocols
Router1#show ip route eigrp
Router1#show ip eigrp neighbors
Router1#show ip eigrp interfaces
Router9#show ip eigrp accounting
Router1#show ip eigrp topology
注释 12.3(14)T引入了show ip eigrp accounting
Router9#show ip eigrp accounting
IP-EIGRP accounting for AS(55)/ID(172.18.5.9)
Total Prefix Count: 50      States: A-Adjacency, P-Pending, D-Down
State Address/Source       Interface            Prefix       Restart      Restart/
                                            Count         Count       Reset(s)
A        172.20.10.1          Se0/0                     1            0            0
A        172.18.19.1          Fa0/0                    39            0            0
A        172.18.19.4          Fa0/0                     1            0            0
A        172.18.19.6          Fa0/0                     6            0            0
Router1#show ip eigrp topology
IP-EIGRP Topology Table for AS(55)/ID(172.25.25.1)
Codes: P – Passive, A – Active, U – Update, Q – Query, R – Reply,
           r – reply Status, s – sia Status
P 0.0.0.0/0, 1 successors, FD is 28160, tag is 5
             via Rstatic (28160/0)
             via Summary (28160/0), Null0
P 10.2.2.0/24, 1 successors, FD is 156160
             via 172.22.1.4 (256), FastEthernet0/1
P 10.1.1.0/30, 1 successors, FD is 3845120
             via Connected, Serial0/1
P 192.168.10.0/24, 1 successors, FD is 28160, tag is 5
             via Rstatic (28160/0)
P 192.168.30.0/24, 1 successors, FD is 156160
             via 172.22.1.4 (256), FastEthernet0/1
P 192.168.20.0/24, 1 successors, FD is 2195456
             via 172.25.2.2 (600), Serial0/0.2
P 172.25.25.6/32, 1 successors, FD is 156160
             via 172.25.1.7 (256), FastEthernet0/0.1
P 172.25.25.1/32, 1 successors, FD is 128256
             via Connected, Loopback0
P 172.25.25.2/32, 1 successors, FD is 2297856
             via 172.25.2.2 (256), Serial0/0.2
P 172.25.1.0/24, 1 successors, FD is 28160
             via Connected, FastEthernet0/0.1
P 172.25.2.0/30, 1 successors, FD is 2169856
             via Connected, Serial0/0.2
P 172.22.1.0/24, 1 successors, FD is 28160
             via Connected, FastEthernet0/1
& Powered by